Psg 1000 manual

However, in congested RF environments or in close proximity to sources of RF interference such as large LED video panels , the squelch may need to be lowered to prevent excessive audio dropouts. With lower squelch settings, the performer may hear more noise or hiss, but will experience fewer audio dropouts. Important: Before lowering squelch, first try to eliminate the problem by finding the best set of frequencies for your installation and removing potential sources of interference.

Caution: Turning off or lowering the squelch setting can increase the noise level and cause discomfort to the performer:. This allows a transmitter and receiver setup where both units are racked and powered by AC. Each transmitter has an RJ port on the back for connecting to other transmitters over an Ethernet network. Networking transmitters allows you to automatically set frequencies for all the transmitters with a single group scan command.

You can control and monitor all networked transmitters through a computer running Shure Wireless Workbench software, Version 6 or later. If using the default automatic network setting, make sure your computer is configured for DHCP. Note: Some security software or firewall settings on your computer can prevent you from connecting to the transmitter.

If using firewall software, allow connections on port Static IP addressing is also supported. Use this feature to scan the full RF spectrum for potential sources of interference and deploy open frequencies to all receivers on the network.

A graphical representation of the scan data may be viewed on both the transmitter and receiver. This allows you to scroll through the graph to reveal details about the frequency and strength of the interfering signals.

The receiver displays the scan data as a graph and gives options for viewing and deploying. Once the download is complete, the receiver automatically begins the firmware update, which overwrites the existing firmware. Do not turn off the receiver until the update is complete. NOTE: This Radio equipment is intended for use in musical professional entertainment and similar applications.

This Radio apparatus may be capable of operating on some frequencies not authorized in your region. Please contact your national authority to obtain information on authorized frequencies and RF power levels for wireless microphone products. Note: Please follow your regional recycling scheme for batteries and electronic waste.

This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December , this device will comply if it is operated in the MHz frequency band.

KEEP these instructions. HEED all warnings. DO NOT use this apparatus near water. DO NOT block any ventilation openings. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat. Do not place any open flame sources on the product. DO NOT defeat the safety purpose of the polarized or grounding type plug.

A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

Do not subject to extreme force and do not pull on the cable or failures may result. Keep the product dry and avoid exposure to extreme temperatures and humidity. Do not attempt to modify this product. Operation is subject to the following two conditions: This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. Operation is subject to the following two conditions: This device may not cause interference. This device must accept any interference, including interference that may cause undesired operation of the device. Quickstart Instructions Rack Mount Transmitter Connect to a power outlet using the supplied power cable.

Connect the audio source, such as the output of a mixer, to the audio inputs. You can use both input jacks or choose either one for a mono source. Switch RF off and power on. For mono one input , access the Audio menu and select Mono. Adjust the audio source level so that, for the average input signal level, the top two yellow LEDs flicker and the lower LEDs are solid. Bodypack Open by pressing the latches on both sides and pulling. Scan and Sync On the bodypack, press the scan button. Align the IR windows on the bodypack and rack unit, the IR window on the transmitter illuminates.

Press the sync button on the transmitter. Turn the RF switch on. The bodypack also displays the RF signal strength RF. Important: Turn bodypack volume down before plugging in earphones.

Insert the earphones and slowly turn up the volume. Front Panel Controls. Rear Panel. Bodypack Receiver. G Group number. CH Channel number. Audio Settings Access the following audio settings from the Audio menu. Note: The volume limit does not compress the audio signal. Match default Matches the frequency response of legacy PSM receivers, allowing for matched audio with mixed-inventory setups Flat Offers a flat frequency response curve Off Audio bypasses input EQ.

Multiple System Setup When setting up multiple systems, designate a single bodypack to scan for available frequencies and download them to all the rack units. The bodypack must be from the same frequency band as all the transmitters. Power on all the rack units. Turn off the RF. This prevents them from interfering with the frequency scan.

Use the bodypack to scan for a group by pressing and holding the scan button for two seconds. Sync the bodypack with the first rack unit by aligning the IR windows and pressing sync. Press scan again on the bodypack to find the next available frequency. Sync the bodypack with the next rack unit. Repeat with all the rack units. Sync each performer's bodypack to its respective rack unit by aligning the IR windows and pressing snyc.

DO NOT press scan on the bodypacks. Turn on the RF on all rack units. The systems are ready to use. CueMode CueMode allows you to upload the name and frequency settings from multiple rack units and store them as a list on a single bodypack. Open the battery door and press the enter button. Align IR windows and press sync on the rack unit. Repeat the above step for each transmitter. Frequency Scan Use a frequency scan to analyze the RF environment for interference and identify available frequencies.

There are three types of scan: Channel Scan Press the scan button on the bodypack. Finds the first available channel. Group Scan Press and hold the scan button for two seconds. Finds the group with the greatest number of available channels. Each group contains a set of frequencies that are compatible when operating multiple systems in the same environment. Note: When performing a frequency scan: Turn off the RF on the transmitters for the systems you are setting up. Turn on potential sources of interference such as other wireless systems or devices, computers, CD players, large LED panels, effects processors, and digital rack equipment so they are operating as they would be during the presentation or performance so the scan will detect and avoid any interference they generate.

Sync You can transfer frequency settings in either direction: from the bodypack to the rack unit, or from the rack unit to the bodypack. Downloading settings from the bodypack Press the scan button on the bodypack. The level LEDs on the rack unit flash. Sending settings to the bodypack Press the Sync button on the rack transmitter to access the sync menu.

Align the IR windows. When properly aligned the IR window on the transmitter illuminates. Press Sync to transfer settings. The blue LED on the bodypack flashes. Creating Custom Groups This feature allows you to create your own groups of frequencies.

U1, U2, etc. Push the Control wheel to move to the Channel parameter and turn it to select a channel 01, 02, 03, etc. Push the Control wheel to move to the Freq parameter and select a frequency for that channel. Push the Next menu key to select a frequency for the next channel in that group. Select Load to find all other devices of the same model and band on the network.

Then press enter to deploy the custom group list to all these devices. This overwrites all existing custom groups. Clear deletes all custom groups for all devices on the network. MixMode Some performers need to hear more of their own voice or instrument, while others want to hear more of the band. Squelch Squelch mutes audio output from the bodypack when the RF signal become noisy. Caution: Turning off or lowering the squelch setting can increase the noise level and cause discomfort to the performer: Do not lower the squelch setting unless absolutely necessary.

Turn earphone volume to the lowest setting before adjusting squelch. Do not change the squelch setting during a performance. Turn up the transmitter level setting to make noise or hiss less noticeable. MID Moderately decreases the signal-to-noise ratio required to squelch the receiver.

LOW Greatly decreases the noise squelch threshold. Sometimes used as a debugging tool by monitor engineers or RF coordinators to "listen" to the RF environment. Point-to-Point Wireless Audio.

Ethernet Connection Each transmitter has an RJ port on the back for connecting to other transmitters over an Ethernet network. Use Ethernet switches to extend the network for larger installations. Connect transmitters in series. Accessing the Network with a Computer You can control and monitor all networked transmitters through a computer running Shure Wireless Workbench software, Version 6 or later.

Extended Network. Direct Connection to Computer. Spectrum Scan Use this feature to scan the full RF spectrum for potential sources of interference and deploy open frequencies to all receivers on the network. Collect the scan data. Load the scan data from the bodypack receiver to the rack transmitter. Search network for devices. The rack transmitter searches the network for all available transmitters.

OME Optical test transmitter. OME Optical measurement device. ON Optical node with 65 MHz return path. ON , ON Optical nodes. ONR Optical return path receiver. OPM-AS 04 active splitter. OT 1xx Optical transmitter. PCU IP streamer. PSC series Receiver-powered multiswitches. PSG 5way series Green Line multiswitches, 5 inputs. PSG 9way series Green Line multiswitches, 9 inputs. PSG 17way series Green Line multiswitches, 17 inputs. PSQ 5way series multiswitches, Made in Germany.

PSQ 9way series multiswitches, Made in Germany. PSQ 13way series multiswitches, Made in Germany. PSQ 17way series multiswitches, Made in Germany. Requirements for IPTV networks. SCA 32 Single cable solution cascadable. SCA 32 Programmer. SPM 2. PolyCompact base unit, 10 modules. SPM digi PolyCompact base unit, 10 modules. SPM PolyCompact base unit for one module. SPM PolyCompact base unit for two modules. SPM digi PolyCompact base unit for two modules.

SUV Wide range amplifier ter.